• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Fiat 500 Replacement Key Fob

If your remote key fob has stopped working, it may be time to replace the battery. However, if you replace the battery and it is still not working, then the problem is likely to be elsewhere.

At United Locksmith, we specialize in the creation of new keys for classic automobiles. We have all the tools and parts necessary for this type of service.

Dead Coin Battery

A dead battery is the primary cause of your fiat Tipo Key 500 keyfob not locking or unlocking the doors. The battery inside the key fob will deplete quickly in the event that you don't use it frequently enough. If your remote began to show signs of weakness like a loss of range, and then stopped working completely it is likely that the battery is dead.

The battery in the key fob is held in place by steel clips that retain it. If the clips are not tight, they can cause problems with contact that can prevent the remote from receiving power. Use a flathead screwdriver remove the retaining clip and then remove the old battery. Make sure that the battery you choose to use has the same size, voltage and specification as the original.

The key fob might also be damaged or corroded through exposure to water. Even a small bath in soapy, warm water can cause damage to the chip. It is recommended to keep your key fob in a dry area.

Water Damage

If your key fob isn't working properly, it may be caused by water damage. Key fobs come with rubber seals to protect them from being damaged by a light rain or splashes of water, but it is essential to keep your keys away from the pool, ocean, and the washing machine!

The key fob is equipped with an electronic chip that sends a signal car's immobilizer system. The chip is what allows the 500 to lock and start. If it gets wet it won't function.

Try cleaning the internal electronics of your key fob using isopropyl alcohol, or an electronic cleaner to see if they are still good. However, it is probably better to purchase a replacement from a dealer instead of trying to repair the key fob that was submerged in salt water.

While a replacement fob can cost a little money, it is much less expensive than having to pay for your Fiat 500 to be towed to the dealer for repair! You can also make it yourself with a few simple steps. Make sure you have the correct battery type prior to opening your keyfob. This task is much easier than it looks and you can find step-bystep instructions online for virtually any car key fob.

Faulty Chip

The chip in the key fob communicates directly with the immobiliser on your car to ensure that the vehicle will only start when right keys are in place. If the chip is damaged or damaged it won't allow your car to start no matter what you do.

A faulty chip can occur due to many reasons, but most often it is due to water damage or an unresponsive battery. It is best to leave the task to a professional locksmith, who can repair the chip in a short time and at a an affordable cost.

If your key fob will not function after exposure to clean tap or rain water then remove the battery. Wipe down the electronic component using an old towel. If the key fob does not work, there's the possibility that it has damaged components and requires to be replaced.

Some people will turn to their dealer when in need of a new Fiat key fob, but this can be a very expensive option. If you're looking for a low-cost solution to have your Fiat key fob fixed make sure you contact United Locksmith. We have all the equipment and know-how to repair your Fiat fob quickly and professionally. way.

Faulty Receiver Module

fiat 500 key fob key fobs send a signal up to 50 feet to the vehicle, which can unlock and close the doors (and start the vehicle if it has automatic transmissions). There are several reasons why the fob may stop working. This includes a dead battery, water damage, worn out buttons, a receiver issue, signal interference, or malfunctioning chips.

If the fob was placed in the pocket that has been subject to extreme trauma (such as being dropped onto the floor, or washed in the washing machine), it may not be able to connect with the Body Control Module (BCM) of the vehicle. The BCM is a security system that only accepts signals from genuine keys.

You will need to replace the fob if this occurs. A professional locksmith can handle all aspects of the replacement process and can even program a brand new one for your 500. In fact, they can provide you with a clone key that functions like your original fob (and costs less than the price).